A Short Communication for Shipbuilding Industry in Vietnam

##plugins.themes.bootstrap3.article.main##

  •   Dinh Tuyen Nguyen

  •   Danh Chan Nguyen

Abstract

According to Shipbuilding Industry Corporation (SBIC), in 2017, shipbuilding value reached more than VND 3,071 billion, equal to 69% of the plan. Other fields have increased significantly, such as: Ship repair reached VND 488.3 billion, equal to 125% of the plan; supporting industry reached VND 264.5 billion, equal to 123% of the plan. Although shipbuilding has not reached the plan, but looking back on the period from 2008 to now, this field is always in a situation of hardship and bottomless decline because of lack of jobs, these are quite satisfactory numbers. The cause of the decline is due to the world shipping and shipbuilding industry has experienced an extremely difficult period due to the heavy influence of the world economic crisis from 2008 up to now. The Vietnamese shipbuilding and shipping industry is also not out of that situation. For the shipbuilding industry to develop, specific policies, with specific support addresses, are needed, which are well-designed and visionary shipbuilding development programs.


Keywords: Shipbuilding, Industry, Material

References

A. T. Hoang and V. V Le, “Marine pollution and remedies of Vietnamese Government,” Int. J. Recent Eng. Res. Dev, vol. 2, no. 4, pp. 51–55, 2017.

A. T. Hoang and V. V. Pham, “A review on fuels used for marine diesel engines,” J. Mech. Eng. Res. Dev. Res. Dev., vol. 41, no. 4, pp. 54–64, 2018.

V. V. Le and A. T. Hoang, “Fuel and alternative fuel for marine diesel engines,” Int. J. Recent Eng. Res. Dev., vol. 2, no. 7, pp. 142–146, 2017.

H. Anh Tuan and C. Minh Quang, “A mini review of using oleophilic skimmers for oil spill recovery,” J. Mech. Eng. Res. Dev., vol. 41, no. 2, pp. 92–96, 2018.

A. T. Hoang and X. D. Pham, “An investigation of remediation and recovery of oil spill and toxic heavy metal from maritime pollution by a new absorbent material,” J. Mar. Eng. Technol., 2018. https://doi.org/10.1080/20464177.2018.1544401.

A. T. Hoang, “A report of the oil spill recovery and treatment technologies to reduce the marine environment pollution,” Int. J. e-Navigation Marit. Econ., vol. 9, pp. 35–49, 2018.

T. N. Le, M. K. Pham, A. T. Hoang, T. N. M. Bui, and D. N. Nguyen, “Microstructure Change For Multi-Pass Welding Between Austenitic Stainless Steel And Carbon Steel,” J. Mech. Eng. Res. Dev., vol. 41, no. 2, pp. 97–102, 2018.

M. K. Pham, D. N. Nguyen, and A. T. Hoang, “Influence of Vanadium Content on the Microstructure and Mechanical Properties of High-Manganese Steel,” Int. J. Mech. Mechatronics Eng., vol. 18, no. 2, pp. 141–147, 2018.

T. N. Le, M. K. Pham, A. T. Hoang, and D. N. Nguyen, “Microstructures and elements distribution in the transition zone of carbon steel and stainless steel welds,” J. Mech. Eng. Res. Dev., vol. 41, no. 3, pp. 27–31, 2018.

X. D. Pham, A. T. Hoang, and D. N. Nguyen, “A Study on the Effect of the Change of Tempering Temperature on the Microstructure Transformation of Cu-Ni-Sn Alloy,” Int. J. Mech. Mechatronics Eng., vol. 18, no. 4, pp. 27–34, 2018.

X. D. Pham, A. T. Hoang, D. N. Nguyen, and V. V Le, “Effect of Factors on the Hydrogen Composition in the Carburizing Process,” Int. J. Appl. Eng. Res., vol. 12, no. 19, pp. 8238–8244, 2017.

D. N. Nguyen, A. T. Hoang, M. T. Sai, M. Q. Chau, and V. V. Pham, “Effect of Sn component on properties and microstructure Cu-Ni-Sn alloys,” J. Teknol., vol. 80, no. 6, pp. 43–51, 2018.

A. T. Hoang, L. H. Nguyen, and D. N. Nguyen, “A Study of Mechanical Properties and Conductivity Capability of CU-9NI-3SN ALLOY,” Int. J. Appl. Eng. Res., vol. 13, no. 7, pp. 5120–5126, 2018.

A. T. Hoang, D. N. Nguyen, and V. V. Pham, “Heat Treatment Furnace For Improving The Weld Mechanical Properties: Design and Fabrication,” Int. J. Mech. Eng. Technol., vol. 9, no. 6, pp. 496–506, 2018.

V. D. Tran, A. T. Le, V. H. Dong, and A. T. Hoang, “Methods of operating the marine engines by ultra-low sulfur fuel to aiming to satisfy MARPOLAnnex VI,” Adv. Nat. Appl. Sci., vol. 11, no. 12, pp. 34–40, 2017.

A. T. Hoang, “Prediction of the density and viscosity of biodiesel and the influence of biodiesel properties on a diesel engine fuel supply system,” J. Mar. Eng. Technol., 2018. https://doi.org/10.1080/20464177.2018.1532734.

A. T. Hoang, X. L. Bui, and X. D. Pham, “A novel investigation of oil and heavy metal adsorption capacity from as-fabricated adsorbent based on agricultural by-product and porous polymer,” Energy Sources, Part A Recover. Util. Environ. Eff., vol. 40, no. 8, pp. 929–939, 2018.

A. T. Hoang et al., “An absorption capacity investigation of new absorbent based on polyurethane foams and rice straw for oil spill cleanup,” Pet. Sci. Technol., vol. 36, no. 5,pp. 361-370, 2018.

A. T. Hoang, V. D. Tran, V. H. Dong, and A. T. Le, “An experimental analysis on physical properties and spray characteristics of an ultrasound-assisted emulsion of ultra-low-sulphur diesel and Jatropha-based biodiesel,” J. Mar. Eng. Technol., pp. 1–9, 2019.

T. N. McManus and A. N. Haddad, “UV and blue light exposures in an aluminum shipbuilding environment,” Int J Open Sci. Res, vol. 1, no. 6, pp. 15–27, 2013.

N. McManus and A. N. Haddad, “Argon-related fatigue: an investigation in an aluminum shipbuilding environment,” Prof. Saf., vol. 60, no. 10, pp. 47–55, 2015.

N. J. Henry Holroyd and G. M. Scamans, “Environmental Degradation of marine aluminum alloys—past, present, and future,” Corrosion, vol. 72, no. 2, pp. 136–143, 2015.

T. N. McManus and A. N. Haddad, “Use of methanol as a coolant during machining of aluminum in a shipbuilding environment: a failure to assess and manage risk,” in Advanced Materials Research, 2014, vol. 955, pp. 1061–1064.

T. N. McManus and A. N. Haddad, “Chromium emissions during welding in an aluminum shipbuilding environment,” Weld. J, vol. 95, pp. 86–92, 2016.

S. Ferraris and L. M. Volpone, “Aluminium alloys in third millennium shipbuilding: materials, technologies, perspectives,” in The Fifth International Forum on Aluminium Ships, Tokyo, Japan, 2005.

K. Galanis, “Fracture of aluminum naval structures.” Massachusetts Institute of Technology, 2007.

F. Roland, L. Manzon, P. Kujala, M. Brede, and J. Weitzenböck, “Advanced joining techniques in European shipbuilding,” J. Sh. Prod., vol. 20, no. 3, pp. 200–210, 2004.

N. McManus and A. N. Haddad, “Oxygen Levels During Welding: Assessment in an Aluminum Shipbuilding Environment,” Prof. Saf., vol. 60, no. 7, pp. 26–32, 2015.

R. A. Sielski, “Research needs in aluminum structure,” Ships Offshore Struct., vol. 3, no. 1, pp. 57–65, 2008.

J. C. Dutra, R. H. G. e Silva, B. M. Savi, C. Marques, and O. E. Alarcon, “New methodology for AC-pulsed GMAW parameterization applied to aluminum shipbuilding,” J. Brazilian Soc. Mech. Sci. Eng., vol. 38, no. 1, pp. 99–107, 2016.

M. J. Hull and J. L. Abraham, “Aluminum welding fume-induced pneumoconiosis,” Hum. Pathol., vol. 33, no. 8, pp. 819–825, 2002.

Downloads

Download data is not yet available.

##plugins.themes.bootstrap3.article.details##

How to Cite
[1]
Nguyen, D. and Nguyen, D. 2019. A Short Communication for Shipbuilding Industry in Vietnam. European Journal of Engineering and Technology Research. 4, 4 (Apr. 2019), 90-94. DOI:https://doi.org/10.24018/ejers.2019.4.4.1255.