This study focuses on determining the optimum tensile strengths of randomly oriented coir/plantain hybrid fiber reinforced polyester resin composites. The control factors of volume fraction, coupling agent and coir/plantain fiber ratio were used in forming the samples. Tensile test was conducted on the samples of Coir/plantain empty fruit bunch (CEFB) hybrid fibers and coir/plantain pseudo stem (CPS) hybrid fibers reinforced polyester resin composites respectively for the optimum tensile strengths. An OKH-600 Digital Display universal Testing Machine was used for conducting tensile tests in order to establish the control factor levels quality characteristics needed to optimize the mechanical properties being investigated. The highest signal-to-noise ratio (S/N ratio) for the quality characteristics was investigated by applying Taguchi robust design technique for the greater-the-better. The optimum values of the control factors were established for CEFB and CPS hybrid fibers reinforced polyester resin composites. The CEFB hybrid fibers reinforced polyester resin composites has the optimum tensile strength of while CPS hybrid fibers reinforced polyester resin composites has the optimum tensile strength of . The control factors contributed greatly to the tensile strength; and the CEFB hybrid fibers reinforced polyester resin composites are less in tension than that of CPS hybrid fiber.
C. Gaurav, and S. Gaurav, “Mechanical Testing Of Al6061/Silicon Carbide Metal Matrix Composite”, International Journal of Research in Engineering & Applied Sciences, 2(2), pp 220-238, 2012.
F. H. Abdalla, M. H. Megat, M. S. Sapuan and B. B. Sahari, “Determination of volume fraction values of filament wound glass and carbon fiber reinforced composites”, ARPN Journal of Engineering and Applied Sciences, 3(4), pp. 7-11, 2008.
S. Y. Binshan, L. Alrik Svenson and C. Lawrence Bank, “Mass and Volume Fraction Properties of Pultruded Glass Fiber-Reinforced Composites”, Research Report, Composites, 26 (10), Elsevier Science Limited, U.K, 1995.
W. Michaeli, M. Wegener, “Optimum Design of Laminates under Aspects of Strength”, In: Füller J., Grüninger G., Schulte K., Bunsell A.R., Massiah A. (eds) Developments in the Science and Technology of Composite Materials. Springer, Dordrecht. pp 777-782, 1990.
L. A. Carlsson, R. B. Pipes, “On the analysis and design of the end notched flexure (ENF) specimen for mode II testing”, Journal of composite materials, Vol. 20, Issue 6, pp 594-604, 1986.
Asim Shahzad, “Hemp fiber and its composites”, J Compos Mater, 46: 973–986, 2011.
T. P. Sathishkumar, J. Naveen, and S Satheeshkumar, “Hybrid fiber reinforced polymer composites – a review”, Journal of Reinforced Plastics and Composites, Vol. 33(5) 454–471, 2014, DOI: 10.1177/0731684413516393.
S. Siddika, F. Mansura, and M. Hasan, “Physico-Mechanical Properties of Jute-Coir Fiber Reinforced Hybrid Polypropylene Composites”. World Academy of Science, Engineering and Technology, 73, 2013.
S. Jeyanthi and J. Janci Rani, “Improving Mechanical Properties by KENAF Natural Long Fiber Reinforced Composite for Automotive Structures”, Journal of Applied Science and Engineering, 15(3), 275-280, , 2012.
T. Hariprasad, G. Dharmalingam, and P. Praveen Raj, “Study of Mechanical Properties of Banana-Coir Hybrid Composite Using Experimental and FEM Techniques”, ISSN (Print): 2289-4659; e-ISSN: 2231-8380, Volume 4, pp. 518-531, 2013, DOI: http://dx.doi.org/10.15282/jmes.4.2013.16.0049.
M. Khalif, and A. Hussain Bagawan, “Experimental Investigation of Effect of Fiber Diameter on Tensile Properties of Jute – Banana Fiber (Hybrid) Reinforced Epoxy Composite”, International Journal of Engineering Research & Technology (IJERT), 3(6), 2014.
H. Essabir, R. Boujmal, M. Ouadi Bensalah, D. Rodrigue, R. Bouhfid, A. Qaiss, “Mechanical and thermal properties of hybrid composites: Oil-palm fiber/clay reinforced high density polyethylene”, Mechanics of Materials, 98, 36–43, 2016.
Kotresh Sardar, Dr. T. Rangaswamy, Shivakumar, “Fabrication and Investigation of Bending Test on Hybrid (Sisal and Banana) Fiber Reinforced Polyester Composite Material”, International Journal of Recent Development in Engineering and Technology, ISSN 2347-6435(Online) Volume 3, Issue 6, 2014.
K. M. Oksman, and J. F. Selin, “Natural fibers as reinforcement in polylactic acid (PLA) composites”, J. Comp. S. Skrivars ci. Technol., 63, pp. 1317-1324, 2003.
E. C. Okafor, C. C. Ihueze, and S.C. Nwigbo, “Optimization of Hardness Strengths Response of Plantain Fibers Reinforced Polyester Matrix Composites (PFRP) Applying Taguchi Robust Design”, International Journal of Engineering, 26(1), 1-11, 2013.
R. M. Jones, “Mechanics of composite materials”. 2nd Ed. Edwards Brothers, Ann Arbor, 1998.
JMP 6.0.3., “Design of Experiments”, Release 6, SAS Institute Inc., Cary, NC, USA, 2005.
U. C. Okonkwo, C. E. Chukwunyelu, B. C. Oweziem, A. Ekuase, “Evaluation and Optimization of Tensile Strength Responses of Coir Fibers Reinforced Polyester Matrix Composites (CFRP) Using Taguchi Robust Design”, Journal of Minerals and Materials Characterization and Engineering (JCMME), 3(4), 225-236, 2015.
M. Ashby, H. Shercliff, and D. Cebon, “Materials-Engineering, Science, Processing and Design”. University of Cambridge, UK. Published by Elsevier Ltd, 2007.
E. C. Okafor, “Optimal Design and Characterization of Plantain Fiber Reinforced Polyester Matrices”, Ph.D. dissertation, Department Of Industrial/Production Engineering, Nnamdi Azikiwe University, Awka, 2014.
G. U. Raju, V. N. Gaitonde, and S. Kumarappa, “Experimental Study on Optimization of Thermal Properties of Groundnut Shell Particle Reinforced Polymer Composites”, International Journal of Emerging Sciences, 2(3), 433-454, 2012.
MS. Phadke, “Quality Engineering using Robust Design”, Prentice Hall, Englewood Cliffs, New Jersey, 1989.
This work is licensed under a Creative Commons Attribution 4.0 International License.
The names and email addresses entered in this journal site will be used exclusively for the stated purposes of this journal and will not be made available for any other purpose or to any other party.
Submission of the manuscript represents that the manuscript has not been published previously and is not considered for publication elsewhere.