Moment and Stress Analysis Solutions of Clamped Rectangular Thick Plate
##plugins.themes.bootstrap3.article.sidebar##
PDF
Submitted Apr 14, 2020
Published Apr 28, 2020
Published Apr 28, 2020
DOI
Abstract viewed = 208 times
PDF downloaded = 95 times
Issue
Section
Articles
##plugins.themes.bootstrap3.article.main##
The bending solutions of rectangular thick plate with all four edges clamped (CCCC) were investigated in this study. The basic governing equations used for analysis are based on third-order shear deformation plate theory analysis under uniformly distributed load. Using a formulated total potential energy equation, the three coupled general governing differential equations for the determination of the out of plane displacement and shear deformations rotation along the direction of x and y coordinates were obtained. These equations as obtained are solved simultaneously after minimization to determine the coefficients of displacements of the plate and other the mentioned functions. By solving these equations, the analytic solutions of rectangular thick plate with all four edges clamped were derived. From the formulated expression, the formula for calculation of the maximum deflection, moment, stress and in-plane displacements were deduced. The proposed method obviates the need of shear correction factors, which is associated with Mindlin’s theory (FSDT) for the solution to the problem. Moreover, numerical comparison shows the correctness and accuracy of the results.
Keywords: CCCC Plate, Traditional Third-Order Shear Deformation Plate Theory, Shear Correction Factors, Critical Lateral Imposed Load
References
Ibearugbulem, Owus M., Ezeh, John C., Ettu, Lawrence O., Gwarah, Ledum S. (2018). Bending Analysis of Rectangular Thick Plate Using Polynomial Shear Deformation Theory. IOSR Journal of Engineering (IOSRJEN), Vol. 08, Issue 9 (September. 2018), ||V (III) || PP 53-61.
Li Rui; Xiaoqin Ni; and Gengdong Cheng (2014). Symplectic Superposition Method for Benchmark Flexure Solutions for Rectangular Thick Plates. J. Eng. Mech., DOI: 10.1061/ (ASCE) pp. 1-17
Liu, F.-L., and Liew, K. M. (1998). “Differential cubature method for static solutions of arbitrarily shaped thick plates.” Int. J. Solids Struct. 35(2).
Lok, T. S., and Cheng, Q. H. (2001). “Bending and forced vibration response of a clamped orthotropic thick plate and sandwich panel.” J. Sound Vib., 245(1), 63–78.
Mindlin, R.D. (1951), Influence of rotatory inertia and shear on flexural motions of isotropic, elastic plates. ASME Journal of Applied Mechanics, 18 p. 31–38.
Mindlin, R.D., Schaknow, A., Deresiewicz, H., (1956) Flexural vibration of rectangular plates. ASME Journal of Applied Mechanics 23, 430–436.
Onyeka, F. C., Okafor, F. O., Onah, H. N. (2018). Displacement and Stress Analysis in Shear Deformable Thick Plate, International Journal of Applied Engineering Research ISSN 0973-4562 Volume 13, Number 11, pp. 9893-9908.
Onyeka, F. C., Okafor, F. O., Onah, H. N. (2019). Displacement and Stress Analysis in Shear Deformable Thick Plate, International Journal of Applied Engineering Research ISSN 0973-4562 Volume 14, Number 8, pp. 2043-2057.
Reddy J.N (1984) A refined non-linear theory of plates with transverse shear deformation International Journal of Solids and Structures, Vol. 20, pp 881-896.
Reissner, E (1944) On the theory of bending of elastic plates, Journal of Mathematics and Physics 23 184–191.
Reissner, E (1945) The effect of transverse shear deformations on the bending of elastic plates, ASME Journal of Applied Mechanics, vol 12, A69-A77.
Reissner, E., (1975), “On Transverse Bending of Plates, Including the Effect of Transverse Shear Deformation,” International Journal of Solids and Structures, Vol. 11, pp. 569–573.
Reissner, E., (1981), “A Note on Bending of Plates including the effects of Transverse Shearing and Normal Strains,” ZAMP: Zeitschrift fur Angewandte Mathematik und Physik, Vol. 32, pp. 764–767.
Shen, P., and He, P. (1995). “Bending analysis of rectangular moderately thick plates using spline finite element method.” Comput.Struct. 54(6), 1023–1029.
Timoshenko, S. P. (1921), ‘On the correction for shear of the differential equation transverse vibration of prismatic bars’, Philosophical Magazine, Series 6 41, 744–746.
Yang Zhong and Qian Xu (2017). Analysis Bending Solutions of Clamped Rectangular Thick Plate Hindawi Mathematical Problems in Engineering Volume 2017, Article ID 7539276, pp. 1-6.
Downloads
Download data is not yet available.
##plugins.themes.bootstrap3.article.details##
How to Cite
[1]
Ibearugbulem, O. and Onyeka, F. 2020. Moment and Stress Analysis Solutions of Clamped Rectangular Thick Plate. European Journal of Engineering and Technology Research. 5, 4 (Apr. 2020), 531-534. DOI:https://doi.org/10.24018/ejers.2020.5.4.1898.
This work is licensed under a Creative Commons Attribution 4.0 International License.
The names and email addresses entered in this journal site will be used exclusively for the stated purposes of this journal and will not be made available for any other purpose or to any other party.
Submission of the manuscript represents that the manuscript has not been published previously and is not considered for publication elsewhere.
